Certainly! click here for more details on the download manual…..

kubota actv oc60e diesel pressure washer Kubota actv oc60e diesel pressure washer starting up after more than a year standing in a garage. Badly made one handed video …

Kubota OC95-E2 diesel engine sound pretty cool little diesel engine, air and oil cooled also is indirect injection.

Replacing the gearbox seal on a Kubota OC60 E2 or OC95 E2 engine is an important maintenance task that can prevent oil leaks and ensure the longevity of the engine. Below are detailed steps and descriptions of the tools required for this process:

### Tools and Materials Needed

– **Socket Set**: A comprehensive set of sockets (metric sizes) to remove bolts securely.
– **Wrenches**: Open-end and box-end wrenches in metric sizes for various fasteners.
– **Screwdrivers**: Both flathead and Phillips screwdrivers for removing any smaller screws or clips.
– **Pliers**: Needle-nose and regular pliers for gripping and manipulating small parts.
– **Seal Puller**: A specialized tool designed to remove seals without damaging the surrounding components.
– **Razor Blade or Scraper**: For cleaning the surface of the gearbox where the new seal will be installed.
– **Torque Wrench**: To ensure that bolts are tightened to the manufacturer’s specifications.
– **Replacement Gearbox Seal**: A high-quality seal that is compatible with the Kubota OC60 E2 or OC95 E2 engine.
– **Gasket Maker (if applicable)**: Some applications might require a sealant or gasket maker for additional sealing.
– **Cleaning Solvent**: To clean surfaces before installation (such as brake cleaner or degreaser).
– **Shop Towels**: For cleaning up spills and wiping down components.
– **Safety Gear**: Gloves and safety glasses to protect yourself during the process.

### Replacement Procedure

– **Preparation**:
– Ensure the engine is turned off and cooled down. Disconnect the battery to prevent any accidental starts.
– Remove any obstructions that might hinder access to the gearbox area (like protective covers or shields).

– **Drain the Oil**:
– Place a pan under the gearbox to catch any oil that will leak out.
– Remove the drain plug and allow the oil to completely drain out. Replace the drain plug once done.

– **Access the Gearbox**:
– Using the socket set, remove any components that cover the gearbox, such as the drive shaft or other attachments.
– Carefully label and store bolts and components to ensure proper reassembly.

– **Remove the Old Seal**:
– Use the seal puller to carefully extract the old gearbox seal. Be cautious not to damage the surrounding housing.
– If necessary, use a scraper or razor blade to remove any remnants of the old seal.

– **Clean the Seal Area**:
– Clean the area where the new seal will be installed using a cleaning solvent and shop towels. Ensure that the surface is free from dirt, debris, and old sealant.

– **Install the New Seal**:
– Lightly coat the outer edge of the new seal with engine oil to facilitate installation.
– Carefully press the new seal into place using your evenly and flush with the gearbox surface.

– **Reassemble the Gearbox**:
– Reattach any components that were removed to access the gearbox.
– Use the torque wrench to tighten bolts to the manufacturer’s specifications, ensuring they are secure but not over-tightened.

– **Refill Gearbox Oil**:
– Remove the fill plug and pour in the appropriate type and amount of gearbox oil recommended for the Kubota OC60 E2 or OC95 E2 engine.
– Replace the fill plug securely.

– **Final Checks**:
– Reconnect the battery and start the engine to check for leaks around the new seal.
– Allow the engine to run for a few minutes and monitor for any signs of leakage.

– **Cleanup**:
– Dispose of any old oil and materials in accordance with local regulations.
– Clean up the work area and store tools properly.

By following these steps and using the appropriate tools, you can successfully replace the gearbox seal on a Kubota OC60 E2 or OC95 E2 engine. Always refer to the engine’s service manual for specific details and torque specifications.
A wheel lock, often referred to as a wheel lock nut or locking lug nut, is a security device designed to prevent the theft of wheels and tires from vehicles. This component is particularly important for vehicles that have aftermarket wheels, which are often more valuable and desirable to thieves compared to standard factory wheels.

Wheel locks operate by replacing one or more of the standard lug nuts on a vehicle’s wheel with a specialized nut that requires a unique key or tool for removal. Each wheel lock set typically comes with a specific key that fits the unique pattern of the locking lug nut, making it nearly impossible for thieves to remove the wheels without this tool. The design of wheel locks varies, but they often feature a serrated or irregular shape that cannot be gripped by standard tools, adding an additional layer of security.

Installing wheel locks is a straightforward process and can usually be done during a tire change or rotation. While they provide a significant deterrent to theft, it is essential for vehicle owners to keep the locking key in a safe and accessible place, as losing it can result in difficulties when needing to remove the wheels for maintenance or repair.

In summary, wheel locks are an effective anti-theft measure that enhances vehicle security by safeguarding valuable wheels and tires from opportunistic theft, making them a prudent investment for vehicle owners seeking added peace of mind.