Performing a ball joint replacement on a Polski Fiat 125 Pick Up is a task that requires careful attention to detail and the right tools. click here for more details on the download manual…..

Night

Below are the detailed steps and tools you will need for the procedure:

### tools Required:
– **Jack and Jack Stands**: To lift and secure the vehicle safely.
– **Lug Wrench**: For removing wheel nuts.
– **Socket Set**: A range of sockets (typically 10mm to 19mm) to remove bolts and nuts.
– **Torque Wrench**: To ensure bolts are tightened to the manufacturer’s specifications.
– **Ball Joint Separator Tool (or Fork)**: Specifically designed to separate the ball joint from the steering knuckle.
– **Pry Bar**: For leverage when separating components.
– **Hammer**: To assist in separating the ball joint if necessary.
– **Press Tool or Ball Joint Removal Tool**: To remove and install the ball joint.
– **Grease Gun**: For lubricating the new ball joint.
– **Safety Glasses**: To protect your eyes during the process.
– **Work Gloves**: To protect your hands.
– **Shop Manual**: For specific torque specifications and diagrams.

### Procedure:
– **Preparation**:
– Park the vehicle on a level surface and engage the parking brake.
– Gather all necessary tools and materials.

– **Lift the Vehicle**:
– Use the jack to lift the front of the vehicle.
– Secure it with jack stands to ensure stability while you work.

– **Remove the Wheel**:
– Use the lug wrench to remove the nuts from the front wheel.
– Take off the wheel and set it aside.

– **Disconnect the brake Components**:
– If necessary, remove the brake caliper and support it with a Wire to avoid putting stress on the brake line. Do not let it hang.
– Remove the brake disc (if necessary) to gain access to the ball joint.

– **Access the Ball Joint**:
– Locate the ball joint on the lower control arm connected to the steering knuckle.

– **Remove the Ball Joint Nut**:
– Use the appropriate socket to remove the nut securing the ball joint to the steering knuckle.

– **Separate the Ball Joint from the Steering Knuckle**:
– Use the ball joint separator tool to carefully separate the ball joint from the steering knuckle. If it is stuck, tap the tool gently with a hammer to loosen it.

– **Remove the Ball Joint**:
– If the ball joint is press-fitted into the control arm, use a ball joint press tool to push it out from the control arm. Follow the tool’s instructions for proper use.

– **Install the New Ball Joint**:
– Lubricate the new ball joint as required.
– Position the new ball joint in the control arm and use the ball joint press tool to install it firmly.

– **Reattach the Steering Knuckle**:
– Align the steering knuckle with the new ball joint and secure it with the nut.
– Torque the nut to the manufacturer’s specified torque using a torque wrench.

– **Reinstall brake Components**:
– Reattach the brake disc and caliper (if removed) ensuring everything is tightened to specification.

– **Reattach the Wheel**:
– Place the wheel back onto the hub and hand-tighten the lug nuts.

– **Lower the Vehicle**:
– Carefully remove the jack stands and lower the vehicle back to the ground using the jack.

– **Final Tightening**:
– Once the vehicle is on the ground, use the lug wrench to fully tighten the wheel nuts in a criss-cross pattern to ensure even tightening.

– **Test Drive**:
– Take the vehicle for a short test drive to ensure everything is functioning correctly and check for any unusual noises or handling issues.

### Safety Precautions:
– Always wear safety glasses and gloves during the procedure.
– Ensure the vehicle is secure on jack stands before working underneath it.
– Consult the shop manual for any specific instructions related to your vehicle model.

This detailed guide should provide a comprehensive overview of how to replace the ball joint on a Polski Fiat 125 Pick Up. Always refer to a professional mechanic if you are unsure about any steps in the process.
Hazard lights, also known as hazard warning lights or emergency flashers, are a critical safety feature found in vehicles. these lights are designed to alert other drivers that a vehicle is stationary, experiencing a malfunction, or otherwise poses a potential hazard on the road. When activated, the hazard lights illuminate all four turn signal lights simultaneously, producing a flashing pattern that is highly visible to other road users.

The primary purpose of hazard lights is to enhance visibility in situations where a vehicle may be obstructing traffic or is otherwise in danger. For instance, if a driver has to pull over due to a mechanical failure, flat tire, or medical emergency, activating the hazard lights communicates to other drivers that caution is necessary. This can help prevent accidents, as it signals that the vehicle is not moving and may be an obstacle.

To activate hazard lights, drivers typically use a switch located on the dashboard, often marked with a red triangle symbol. The function is straightforward: pressing the switch engages the hazard lights, and pressing it again deactivates them. It’s important for drivers to remember that hazard lights should be used judiciously and not while the vehicle is in motion, except in specific scenarios where it is necessary to alert others to a dangerous situation. Understanding the proper use of hazard lights is essential for promoting safety on the road.